Up late club

steveo · Post by **steveo** » Sat Dec 05, 09 1:17 am

hemi met the dyno

mopar_mark · Post by **mopar_mark** » Sat Dec 05, 09 1:17 am

No bed yet, gonna have coffee & unwind

mopar_mark · Post by **mopar_mark** » Sat Dec 05, 09 1:20 am

Well there where some good points, but still can't sort out the 2 step ? Once I get to 2,800rpm, it goes kin crazy, pulls back RPM, adds fuel ?

Top end was fine, smoothed out some of the transition, made reasonable power, 725 @ the rear @ 5,800rpm & climbing

Idle has gone to pot !

Anonymous · Post by **Anonymous** » Sat Dec 05, 09 1:25 am

mopar_mark wrote:Well there where some good points, but still can't sort out the 2 step ? Once I get to 2,800rpm, it goes kin crazy, pulls back RPM, adds fuel ?

Top end was fine, smoothed out some of the transition, made reasonable power, 725 @ the rear @ 5,800rpm & climbing

Idle has gone to pot !

, plug leads hangin off? , seem to remember it made gobs of torue well below 5,800.

mopar_mark · Post by **mopar_mark** » Sat Dec 05, 09 1:26 am

Couple of options on the table, by pass Big Stuff 3 & use MSD for the 2 step

Dump the BigStuff 3

, switch to a FAST System

Who knows, bit dejected really, but will get over it or overcome it, how ever you want to say it.

Also got a nice nail in my slick from some where ! wasn't expecting to have to repair a puncture today

mopar_mark · Post by **mopar_mark** » Sat Dec 05, 09 1:28 am

Brutus wrote:
, plug leads hangin off? , seem to remember it made gobs of torue well below 5,800.

725 at the rear wheels, not the crank, taking 25% loss through the trans, puts it back in the same ball park

Anonymous · Post by **Anonymous** » Sat Dec 05, 09 1:29 am

I am pee off as well just spent hours drawing the suspention brackets and cant seem to open the drawing I think I have lost it will have to start all over again Grrrrrrrrrrrrrrrrrr

Anonymous · Post by **Anonymous** » Sat Dec 05, 09 1:29 am

I'm sure you'll sort it Mark.

Anonymous · Post by **Anonymous** » Sat Dec 05, 09 1:30 am

Hi Mark thats not good mate have to give it an
800 shot of nos like brutus

mopar_mark · Post by **mopar_mark** » Sat Dec 05, 09 1:31 am

Knightcharger wrote:I am pee off as well just spent hours drawing the suspention brackets and cant seem to open the drawing I think I have lost it will have to start all over again Grrrrrrrrrrrrrrrrrr

Open the Autocad or what ever, then you normally get a chance to select from the last working file

mopar_mark · Post by **mopar_mark** » Sat Dec 05, 09 1:32 am

Knightcharger wrote:Hi Mark thats not good mate have to give it an
800 shot of nos like brutus

Thought he was gonna up with a 2 stage

Anonymous · Post by **Anonymous** » Sat Dec 05, 09 1:33 am

Hey Bob , mind what you say , Mark might want that ole Koffle back.

Anonymous · Post by **Anonymous** » Sat Dec 05, 09 1:34 am

Sheepish grin on my face

mopar_mark · Post by **mopar_mark** » Sat Dec 05, 09 1:36 am

Brutus wrote:I'm sure you'll sort it Mark.

yes, mate.... at least I got a bit of time, till next season

Brutus wrote:Hey Bob , mind what you say , Mark might want that ole Koffle back.

Yeah, I could do with another shopping motor

Anonymous · Post by **Anonymous** » Sat Dec 05, 09 1:36 am

Have done that it sayus that the file is being used by the PC even after I have rebooted it the preview shows it as blank but the properties say there is 73k of poo in there spomewhere?