Up late club

Anonymous · Post by **Anonymous** » Sat Dec 05, 09 1:37 am

BUmp I am so annoyed I cant even spell

mopar_mark · Post by **mopar_mark** » Sat Dec 05, 09 1:39 am

Knightcharger wrote:Have done that it sayus that the file is being used by the PC even after I have rebooted it the preview shows it as blank but the properties say there is 73k of poo in there spomewhere?

73k, that's not the whole file is it ? borders & Bananarama!, take up more file space than that

Anonymous · Post by **Anonymous** » Sat Dec 05, 09 1:42 am

No Mate it is only a few sketches for the fabricator but it has my base dimensions on it I am useing a new version, Autocad 2009 and just getting the hang of it maybee did not save correctly need a tardis to go back in time for a day.

mopar_mark · Post by **mopar_mark** » Sat Dec 05, 09 1:47 am

That's a pi55er, you never know, dims will come back to you, when you start again

Anonymous · Post by **Anonymous** » Sat Dec 05, 09 1:48 am

E mailed it to you Mate

mopar_mark · Post by **mopar_mark** » Sat Dec 05, 09 1:49 am

Knightcharger wrote:E mailed it to you Mate

which one ?

sheridan.m.2@pg.com

sheridanmark@aol.com

Anonymous · Post by **Anonymous** » Sat Dec 05, 09 1:53 am

sheridan.m.2@pg.com
B

mopar_mark · Post by **mopar_mark** » Sat Dec 05, 09 1:54 am

Knightcharger wrote:sheridan.m.2@pg.com
B

Got it, need to fire up my other laptop, give me a few minutes

Anonymous · Post by **Anonymous** » Sat Dec 05, 09 2:01 am

Cheers mate I olso had the wrong trans shield delivered by Summit they shoe two sorts from CRS an 826 and an 836 both are listed as fitting a 727 but the 826 has three fixing holes on the top and the 836 only two.
Just my luck that I got the three hole one that do4s not fit.
Anyway they have agrred that they will swap it out and pay for the shipping.
I also ordered the wrong electric waterpump, it fitted to the standard waterpump casting and I wanted the billet type so they have agreed to swap that over as well so all is not lost just have to wait a few weeks.
That Easter Thunderball is looking mighty soon all of a sudden.
I figure allowing for test and tune I only have 7 to 8 weeks to get it finished.

mopar_mark · Post by **mopar_mark** » Sat Dec 05, 09 2:05 am

glad there sorting it for you.

You can get a lot done in 8 weeks, 56 days......... That's 1300 Hours

Anonymous · Post by **Anonymous** » Sat Dec 05, 09 2:08 am

I wish

If I did that I think I might be single again.

Actaually that's not a bad thought

mopar_mark · Post by **mopar_mark** » Sat Dec 05, 09 2:11 am

Bob,
Just get drawing recovery....

Do you have the option for the BAK file, try doing a search on your C or main drive for *.bak

Anonymous · Post by **Anonymous** » Sat Dec 05, 09 2:14 am

Yep it must be there somewhere I am going to sleep on it and try again tommorow I can always get the dims of the car and start again.
Good luck sorting the motor out see you soon.
Night
B

mopar_mark · Post by **mopar_mark** » Sat Dec 05, 09 2:17 am

Night

Anonymous · Post by **Anonymous** » Sat Dec 05, 09 2:41 am

early birds!!!!!!!!!!!