Half shaft bearing number ?

Mossy68 · Post by **Mossy68** » Thu Aug 28, 14 8:10 pm

Can anyone tell me the correct Timken number for an 8 3/4 tapered half shaft bearing.
Think I may have been mis sold the wrong ones.

TIA.

Mossy68 · Post by **Mossy68** » Sun Aug 31, 14 10:37 pm

Anyone ???
Plenty of kits available from both Yukon and Timken but no numbers. !

Johnny Dart · Post by **Johnny Dart** » Sun Aug 31, 14 10:55 pm

Mossy68 wrote:Anyone ???
Plenty of kits available from both Yukon and Timken but no numbers. !

This might not help , if you are trying to get the new bearing before you remove the old one

Most all bearings have the sizes stamped into the race and roller. Once you have them, you can contact your local bearing supplier, for a match.

There must be loads of suppliers on USA eBay, that's where my new ones came from. £4 USA, $49 - £80 UK.

Mossy68 · Post by **Mossy68** » Sun Aug 31, 14 11:10 pm

Johnny Dart wrote:
Mossy68 wrote:Anyone ???
Plenty of kits available from both Yukon and Timken but no numbers. !
This might not help , if you are trying to get the new bearing before you remove the old one

Most all bearings have the sizes stamped into the race and roller. Once you have them, you can contact your local bearing supplier, for a match.

There must be loads of suppliers on USA eBay, that's where my new ones came from. £4 USA, $49 - £80 UK.

Thanks JD , but I already have the bearings but come up as a manual gearbox bearing ! Maybe the same ? Therefore the question.
Timken M201011 is what I have ?

Johnny Dart · Post by **Johnny Dart** » Mon Sep 01, 14 7:58 am

Sorry,misunderstood the question a bit

This is the sizes of an 8 3/4 axle half shaft bearing.

Johnny-
The RP400 Bearings have the following measurements:

- 2.875" OD
- 1.565" ID
- 1.140" Height

I know you still don't have a Timken part number, but you can measure them , and see if the size is the same.

Mossy68 · Post by **Mossy68** » Mon Sep 01, 14 8:42 am

Johnny Dart wrote:Sorry,misunderstood the question a bit

This is the sizes of an 8 3/4 axle half shaft bearing.

Johnny-
The RP400 Bearings have the following measurements:

- 2.875" OD
- 1.565" ID
- 1.140" Height

I know you still don't have a Timken part number, but you can measure them , and see if the size is the same.

Cheers JD.

latil · Post by **latil** » Mon Sep 01, 14 9:24 am

Part number comes up as manual trans output bearing?

Mossy68 · Post by **Mossy68** » Mon Sep 01, 14 5:16 pm

Cup and cone are M201047 /M201011. Which comes up as Timken set 7.
Which is also for axle.
Does that sound right ?

( havnt had chance to measure the ones I have )

Mossy68 · Post by **Mossy68** » Mon Sep 01, 14 10:23 pm

According to My Mopar website.

1958to1969 Dana Power lok suregrip 741/742
Timken cone 25590
Timken cup 25520.

Now I'm lost

Oh this is for my blown and injected Hemi 71 Duster project I've kept quiet and NOT a more door !!!!!!

Mossy68 · Post by **Mossy68** » Wed Sep 03, 14 10:04 pm

Looks like I'll have to get the vernier out then !

terryr · Post by **terryr** » Sun Sep 07, 14 6:21 pm

take the old bearing or part number to a bearing shop ,that number probably goes in many things ,not just automotive ,or they can crossmatch for a different make ,cant remember the last time I bought one from a car supplyer ,I just go to the bearing shop ,also good for v belts and drive belts ,and half the cost

Mossy68 · Post by **Mossy68** » Sun Sep 07, 14 6:35 pm

terryr wrote:take the old bearing or part number to a bearing shop ,that number probably goes in many things ,not just automotive ,or they can crossmatch for a different make ,cant remember the last time I bought one from a car supplyer ,I just go to the bearing shop ,also good for v belts and drive belts ,and half the cost

Cheers Tel.